Blogger friend, Charge it could not function so there is some possibility of damage: The damage occurred on the appliance rechargeable (charger) battery itself, try your charger on the mobile device and another similar to find broken or not. Battery is damaged on your mobile phone can also be so battery can no longer be refilled. Check if the battery recharge connector on your phone is still good. Then we just do the inspection and testing of the phone itself.
* If your screen appears the message "Not Charging" or cell phone refill process (charging), but the indicator Rechargeable battery runs without charge or refill process (charging) but refill indicator did not say anything then surely its IC Charge damaged. Replace with new IC Charge
* Mobile phones are finished rechargeable (battery full), but the refill indicator keeps going on, then his power IC damaged. Replace it with a new Power IC.
* The phone is not in a state rechargeable (charge), but the refill indicator road continues, then the software (SW) are damaged. Do the program (flash) on the phone with the same version.
* The phone will be done every refill process (charge) is always dead, then the Charge or IC Power IC damaged. Perform inspection and further testing on the phone to determine whether IC or IC Power Charge and then replace the damaged IC or IC Power Charge damaged.
* After charging (charge) phone with a charger, no leaks before the electrical power-on button is pressed, when you press the power button-on, the phone does not work. The cause of the problem is electrical leakage in power supply capacity. The goal remains the Power IC, IC UI, PA IC that is connected to the voltage batteryt VBATT, the units are often damaged and can create problems is the Power IC, IC UI. Because Power is a BGA IC, the IC is integrated, then the method that is usually done is to remove IC UI, then recharge (charge) returned the phone, note whether there is electricity kobocoran. If not, then IC UI damaged, if any, means the power IC damaged. The problem is completed, after the replacement IC above.
* We recharge (charge) the phone, then press the ON button, but the phone did not fire, no electric current that goes into the phone. If so then take the measurement on the R224, if both ends do not have the VBAT voltage is 3.2 V, the mean IC Power is damaged or there is a poor soldering on the IC power. Power IC Replace damaged or re-do the soldering on the IC Power.
* Try to re-flash your phone manner.
* If your screen appears the message "Not Charging" or cell phone refill process (charging), but the indicator Rechargeable battery runs without charge or refill process (charging) but refill indicator did not say anything then surely its IC Charge damaged. Replace with new IC Charge
* Mobile phones are finished rechargeable (battery full), but the refill indicator keeps going on, then his power IC damaged. Replace it with a new Power IC.
* The phone is not in a state rechargeable (charge), but the refill indicator road continues, then the software (SW) are damaged. Do the program (flash) on the phone with the same version.
* The phone will be done every refill process (charge) is always dead, then the Charge or IC Power IC damaged. Perform inspection and further testing on the phone to determine whether IC or IC Power Charge and then replace the damaged IC or IC Power Charge damaged.
* After charging (charge) phone with a charger, no leaks before the electrical power-on button is pressed, when you press the power button-on, the phone does not work. The cause of the problem is electrical leakage in power supply capacity. The goal remains the Power IC, IC UI, PA IC that is connected to the voltage batteryt VBATT, the units are often damaged and can create problems is the Power IC, IC UI. Because Power is a BGA IC, the IC is integrated, then the method that is usually done is to remove IC UI, then recharge (charge) returned the phone, note whether there is electricity kobocoran. If not, then IC UI damaged, if any, means the power IC damaged. The problem is completed, after the replacement IC above.
* We recharge (charge) the phone, then press the ON button, but the phone did not fire, no electric current that goes into the phone. If so then take the measurement on the R224, if both ends do not have the VBAT voltage is 3.2 V, the mean IC Power is damaged or there is a poor soldering on the IC power. Power IC Replace damaged or re-do the soldering on the IC Power.
* Try to re-flash your phone manner.
Labels: Phone Service
0 Comments:
<< Home | << Add a comment